Netview Series
Part No. NPW617HD-24 - Case 6-120365-79257 - How to replace AD Board Inverter?
Before your work, please make sure that the power is disconnected. Step 1: Remove all the LCD panel screws. (12 screws, 3 on each sides). Step 2: Remove the LCD panel frame. Step 3: Remove the LCD mounting screws on the back of the unit. (4 for each ...
Part No. NVP119S8e-KOR - Case 6-OW-111019-79233 - How to rework LVDS Cable?
Before your work, please make sure that the power is disconnected. Step 1: Remove all the LCD panel screws. (11 screws) Step 2: Remove the LCD mounting screw carefully in case of damage LCD panel. (8 screws) Step 3: Unplug the LVDS & inverter as ...
Part No.: NVP117b - 6-OW-107968-78373 - Questions: How to Replace LCD Panel?
(1) Before your work, please make sure that the power is disconnected. Step 1: Remove all the LCD panel screws. (11 screws) Step 2: Remove the LCD mounting screw carefully in case of damage LCD panel. (8 screws) Step 3: Unplug the cable connected to ...
Part No. NVP117-S801e - Case-6-OW-103662-78353 - Question: How to remove and change internal Power Adapter?
“Before your work, please make sure that the power is disconnected.” Step 1: Remove the top rear kit cover. 7 screws on the top, 4 screws on each side. Step 2: After cover removed, cut off the cable tie and disconnect the power adapter. Then replace ...
Part No. NVP117e - Case 6-120748-78317 - How to remove and change the rear kit on NVP117e (Upgrade from AC to 12V DC Power)
Before your work, please make sure that the power is disconnected. Step 1: Remove the top rear cover behind the LCD panel. Step 2: Remove the small top cover behind the LCD panel. Step 3: Unplug four connectors from the original unit as shown below, ...
Part No.: NVP117C8e+ Video Input - Case-6-OW-109039-78264 - Question: How to hard reset to factory default?
Assuming the unit is on AV (BNC) mode. Please try to do the following: Press the “U turn” button to call up the on-screen video mode on top right corner. Use up/down arrow to select the VGA mode. Press the “enter” button to confirm the selection.
Part No. NW119C16e - Case 77983 - How to Reset Cat5/6 KVM to Factory Default
How to Reset Cat5/6 KVM to factory default The KVM can be reset on the KVM PCB board. Open the KVM top metal cover. Find the jumper J2(on red board) or J3(on green board), then use either paper clip or scissors to touch the two boxes of J2 then plug ...
Case 77903 - Part No. NW119C16e - How to replace touchpad or trackball module?
To replace the touchpad or trackball module. Before your work, please make sure that the power is disconnected. Step 1: Take out the black dot (9pcs in red circle as shown below) in order to access the screws on keyboard cover by using cutter. Step ...
Part No. NVP2419WT-S801b - Case 6-OW-110464 - Instruction on Inspecting LVDS Cable ~ NVP2417 / NVP2419 Series
Before your work, please make sure that the power is disconnected. Step 1: Remove all the LCD panel screws. (13 screws) Step 2: Remove the LCD mounting screw carefully in case of damage LCD panel. (4 screws) Step 3: Unplug the LVDS cables carefully ...
Part no: NPW617HD-TRB-24 - Case 6-120349 - Question: Screen does not look whole because it is displaced from its original position.
Issue: Screen does not look whole because it is displaced from its original position Solution: Open the LCD front frame then place it from its original position. Before your work, please make sure that the power is disconnected. Remove all the LCD ...
Part No.: NPW617HD - Case-6-120349 - Question: How to add 24VDC Power into Model: NPW617HD
Before your work, please make sure that the power is disconnected. Step 1: Release total of 11 screws (3 on top, bottom & left-side and 2 on right-side). Step 2: Remove the LCD front frame. Step 3: Remove the tape at the back of LCD panel & unplug ...
Part No.: NVP117-S801e-H - Question: Does the HDMI port also support the USB aspect of the KVM or Video only?
Question: NVP117-S801e-H, for clarification purposes, does the HDMI port below also support the USB aspect of the KVM or is it video only? Meaning, would the HDMI port have keyboard functionality as well? We are quoting our customer and want to make ...
Part No. NW119C16e - Problem: All server buttons are inoperative. No server number light, screen flickers yellow/orange.
Problem: All server buttons are inoperative. No server number light, screen flickers yellow/orange. Diagnosis: PCB Board is defective. See below on how to change the PCB Board. Before your work, please make sure that the power is disconnected. Step ...
Part No.: NVP119-S801b - Case 75909 - Question: Is adding an auxiliary USB port or (ideally) two to the NVP119-S801b possible?
Question: Is it possible to add an auxiliary USB port or (ideally) two to the NVP119-S801b, 12-669-B. We want to be able to plug in a USB device and have it connected through the KVM. Answer: 1. If you want the USB device to be used on all 8 PCs – ...
Part no: NVP117e-12V-Spell - Case 6-111055 - Question: Damaged power cable?
Question: We have damaged a power cable on a system and are requesting for an additional one. Answer: The unit does come with a built in DC 24VDC Terminate Block + and -, thus no external power adapter will be included. And the Power cable wasn’t ...
Part no: NVP3DW16b-HDMI - Case 6-110798 Question: Can't get the drawer to move in or out?
Issue: The purple slide release tab are inside the rail and the unit can't be pulled out or push in. I managed to get some strings looped into the purple release tabs and can pull them, but still can't get the drawer to move in or out. Solution: The ...
Part No.: NVIP117162e - Case 109950 _ Question: How to reset Combo KVM Board (standalone KVM)
Question: Hello iTech team. I am having some issues with the new KVM recently ordered and installed in Dallas. I was able to setup the NVIP117162e (SN/S2027790520125-1120G001-109950) and get it added to the network but when I add the extender NVS1601 ...
Part No.: NVIP117162e - Case 6-OW-109950 - Question: KVM IP Module Compatibility?
Question: I am having problems using the Remote Console option on all of our I-Tech KVMS. It does not matter anymore which browser I use but I always get the Browser has no Java message even though I have downloaded Java. Also, I just want to make ...
Part no.: NVP2DW17HBe-R - Case 111016 - Question: How does these KVM Video Keyboard cables work with NVP2DW17HBe-R?
Cable#1: For Center display (DVI-D signal input + USB for keyboard + USB for mouse) Cable#2: For Right display (DVI-D signal input), pls disregard the VGA & USB connector in this cable which are of no use so we tightened them. *You will need to ...
How to Change the IP Module on 16-Ports KVM LCD Keyboard Console - Model: NVIP117162e
Before your work, please make sure that the power is disconnected. 1. Remove the top rear kit cover. 7 screws on the top, 4 screws on each 2. Disconnect the connection board and remove the 2 hexagon nut to replace the IP network module. 3. Follow ...
How to Reset KVM Password on Combo Version
Click the link below How to Reset KVM Password on Combo Version
How to change N Keyboard NVP Series
Click the link below How to change N Keyboard NVP Series
Resetting new IP KVM password to Default Value
Click the link below Resetting new IP KVM password to Default Value
How to Reset KVM Password on PS2 Version
Click the link below How to Reset KVM Password on PS2 Version
How to Reset KVM Password on Cat6 Matrix Version
Click the link below How to Reset KVM Password on Cat6 Matrix Version
How to connect NE-6 Cable
Click the link below How to connect NE-6 Cable
How to Reset KVM Password on old PS2 Version
Click the link below How to Reset KVM Password on old PS2 Version
How to change KVM Rear Kit on 1U NVP Series
Click the link below How to change KVM Rear Kit on 1U NVP Series
How to change NX and SNK Touchpad/Trackball
Click the link below How to change NX and SNK Touchpad/Trackball
How to remove and replace DVI KVM Board for Rear-Kit
Click the link below How to remove and replace DVI KVM Board for Rear-Kit
How to reconnect the Power Cable
Click the link below How to reconnect the Power Cable
How to check the Internal Power Adapter for NVP with KVM Series
Click the link below How to check the Internal Power Adapter for NVP with KVM Series
How to check Internal Power Adapter Status for NVP Series
Click the link below How to check Internal Power Adapter Status for NVP Series
Remove and Replace instruction Keyboard for NVP "Ge" and "Gb"
Click the link below Remove and Replace instruction Keyboard for NVP "Ge" and "Gb"
Automatic Scale UHD and HD resolutions on the incoming HDMI2.0 Input Signal Model: NPW117K
Question: Will the monitor NPW117K automatically scale if switched between UHD and HD resolutions on the incoming HDMI2.0 input signal? Answer: As HDMI is a digital signal, it’ll automatically scale the resolution.
NVP120S8e Volatility
Click the link below NVP120S8e Volatility
Remove and Replace instruction Keyboard for NK-2
Click the link below Remove and Replace instruction Keyboard for NK-2
NVP2D-3D Series User Manual
Click the link below NVP2D-3D Series User Manual
Instruction to change internal railway NVP2D/ NVP3D/ NP2D/NP3D Series
Click the link below Instruction to change internal railway NVP2D/ NVP3D/ NP2D/NP3D Series
How to know Netview KMV Firmware Version
Click the link below How to know Netview KMV Firmware Version
Next page