General
Part No.: RCK-411 - Case 6-121222-80214 - Question: How to replace keyboard
From the back of the unit, remove the keyboard holder by unscrewing the six screws. Remove the old keyboard and install the replacement. Ensure the keyboard bumper is properly aligned with the notch in the holder. Reattach the keyboard tray to the ...
Part No. EMCW1560-i5 - Case 6-OW-106213-80276 - How to check CMOS Battery?
Power Off the Panel PC Shut down the operating system properly. Disconnect the Panel PC from its power source. Unplug all external cables for safety. Access the Internal Components Place the Panel PC on a stable surface. Remove the rear cover or ...
Part No. U4600P1 - Case 6-OW-109907-79223 - How to check AD board LVDS Cable
AD board LVDS Cable Check Procedure Step 1. Label check Step 2. Loosed rear enclosure around screws ( blue marked ). Step 3. Removed sensor cable carefully ( red marked ) Step 4. Lifted open the rear enclosure slowly ( green marked ). Step 5. a. ...
Part No. TPW24-i5-TR-AC2 - Case 6-OW-120421-80116 - User Manual
Click below link to Download User Manual - Model: TPW24-i5-TR-AC2
Part No.: Amil-1900-D12e-AC - Case 6-OW-111033-80067 - How to Replace Front Panel Plate
1. Remove screws x 3 at both sides 2. Remove screws x 2 at the top 3. Remove screws x 6 to open the LCD back cover 4. Remove screws x 10 to remove handles and replace bended aluminum parts
Part No.: YRM2130-M2 - Case 6-121089-79980 - Panel Replacement Procedure
21.3” Panel Replacement Procedure Step 1: Loosed rear enclosure’s screws (blue marked). Step 2: a. Removed the rear enclosure b. Removed speaker socket ( red marked ) Step 3: a. Removed USB cable ( red marked ) b. Loosed DVI screw ( orange marked ) ...
Part No. U4600P1 - Case 6-121109-80015 - Engineering Change Notice
Description of Change: Back Box Design and I/O Port Relocation for 46" Portrait LCD Monitor (Model: U4600P1). Impact on Product: Outer Dimensions: No change. I/O Port: Relocated at the bottom. Performance: Improved rain and water resistance. Reason ...
Part No. U4600P1-PCAP - Case 6-121109-79523 - Step-by-Step Solution for Removing Condensation:
1. Pre-Heating Preparation a. Ensure Proper Ventilation • Make sure the enclosure has at least one intake vent at the bottom for air to enter and one exhaust vent (if possible) at the top for air to exit. • The intake vent should be unobstructed, ...
Part No. EPMW2700HDWV-DC-V2 - Case 6-120670-79343 - How to replace Power Board
Step 1: Loosed the rear cove Left/Right/Up/Down screws----blue marked Step 2: Removed the rear cover slowly---red marked Noted: When you remove the rear cover, please pay more attention to the inner speaker cable and the inner power cable---green ...
Part No. YOP1700HB2-TCG-TK1 - Case 6-120666-78967 - How replace Open Frame Touch and Panel LCD
Tools 17" Opem Frame Touch LCD Monitor Nylon Gloves Fishing Line Resistive Touch 3M double sided tape 1.55mm Screw Driver Replace Steps 1. Unscrew 8 screws on the rear cover. 2. Lift up middle housing and disconnect LCD cable / LED cable / Touch ...
Part No. iAP-1700 - How to calibrate Touchscreen
Tool Property Page Calibration, draw test tools and the linearity curve of the touchscreen were list in this property page shown as below for user to do touchscreen calibration and touch position test. User can do calibration or draw test by pressing ...
Part No. AK201e-FR - Case 6-120995-79100 - Question: How to replace Keyboard Controller
1. Remove screw x 4 from the bottom. 2. Remove screw x4. 3. Remove up cover 4. Replace keyboard controller
Part No. YOP1700HB2WT-TR - Case 6-OW-110713-78854 - Question: How to update the Touch FW Firmware of PCAP Touch
Afte changing from 5-Wire Resistive Touch to PCAP Touch, need to update the Firmware of PCAP Touch. Completely unzip the archive and execute the update archive "eGalaxUpdate2.exe" Download link below. ...
Part No. AMAR1900HB-TR - Case 6-OW-120877-78840 - Question: How to change from AC to DC
Step 1. Remove screw x 14 to open back cover. Step 2. Remove 5 components but keep all the connections. Step 3. Remove screw x 4 to remove this bracket. Step 4. Attached the new bracket. Step 5. Attach copper stud x 4 and stable DC9~36V power module. ...
Part No. YCHW1210HB2-TR-SK01 - Case-6-OW-111079-78732 - Question: How to replace Power Board?
How to replace Power Board Step 1. There are eight locking screws on the back cover of the screen, which can be removed directly with a cross screwdriver. Step 2. When opening the back cover, please note that there are three cables connected with it. ...
Part No. CCPCW4300HDi7-PCAP-V4 - Case-6-120672-78550 - Question: How to replace LCD Panel?
Step 1 Loosed the maintenance cover screws and removed it. ( blue marked ). Step 2 Removed Input power cable ( yellow marked ). Removed Power Switch cable ( blue marked ). Removed cooling Fan power cable ( red marked ). Removed PC OSD cable ( orange ...
Part No. YFMW2150-PCAP - Case 6-120705-78302 - 21.5'' Flat Surface Multi Touch Monitor (Panel Replacement SOP)
Step1: Flip monitor to rear side and then remove the foam tape at 4 sides. Step 2: Loosen the 14 screws at the rear cover and keep it safe. Step 3: Caution! DO NOT lift up rear cover at this step in case to broken the flexible flat cable of touch ...
Part No. NmilW1730K-DC - Case-6-120280-78117 - Question: MENU is shutting off immediately if there is no video present.
Issue: MENU is shutting off immediately if there is no video present. Solutions: Change the timer for MENU Transparency. Multi Windows Settings Other Settings
Part No. YOP1040HB2 - Case 6-OW-110879-77960 - Question: How to replace LCD Panel & LED Driving Board
Replacing Steps: Step1: Flip to rear side of the monitor , loosen M3 screws*6 and keep it. Step2: Put rear housing aside and disconnect LED Cable & Backlight Cable Step3: Loosen the screw of LED Driving Board and keep it (Orange area) Step4: Put the ...
Part No. ESPM2000B TR - Case 6-120273-78046 - How to replace Power & AD Boards.
1. Remove screws of clamp mount brackets. 2. Remove screws of LCD panel on back housing at left and right sides. 3. Lift up front bezel with LCD touch screen for replace power or AD board 4. Take photos for wires on boards before replacement. 5. ...
Part No. YPM1500PHB2WT-TR - Case 6-OW-110776-77852 - Question: How to safely remove the damaged film to replace with new one.
Issue: Damaged Touch Film Because the touch film has been damaged and turned into atomization. Only removing it will make the display work properly. If there are no other problems with the monitor itself. After removing the Touch, the display screen ...
Part No. BCPCW5500HD-XL - Case 6-120172-77818 - Question: Graphic problem after the monitor worked for several hours.
Issue: Graphic problem after the monitor worked for several hours. Solutions: Change new HDMI cable in the internal PC at the back from PC to AD Board.
Part No. CCHW4300HB-SIP-H - Case 6-120127-77791 - How to remove AD Board
Steps how to remove AD Board Step 1. Loosed the rear maintenance cover screws. ( blue marked) Step 2. Removed some cables and loosed AD board screws. a. Blue marked : 12VDC power cable for AD board b. Yellow marked : GND cable ( AD board ) c. Orange ...
Part No. ASKW2400SX - Case 6-120506 - Installation Guide
Rack Installation Step 1. Loosen screw A on both sides to slide out and remove the two rear slide rails. Step 2. Attach the two rear slide rails to the rear vertical mounting rails of the rank cabinet using standard M6 cage nuts and screws. Step 3. ...
Part No.: BMIL21730-16HDMIe - Case 6-120018 - Question: Hot Key Sequence for selecting input?
Question: Is there is a hot key sequence that will allow you to pick a particular input? Answer: CAPS + CAPS+ 0 + 1 (for ports 01-09) and CAPS + CAPS + 1 + 0 (for ports 10-16)
Part no: iAP-1700-TSRer_USB - Question: Drivers for this Touchscreen Model?
Touchscreen Driver for Model: iAP-1700-TSRer_USB Downlink below https://www.eeti.com/drivers.html
Part No: AMil-W1730-D12b-AC - Case-6-120162 - Question: One of the Trackballs has quit responding. Is there a way to re enable it?
Customer Issue: One of the Trackballs has quit responding. Is there a way to re enable it? Solution: First check if there is dirt/foreign object under the trackball and covering the laser. Re-plug the keyboard internal cable. See below instruction.
Part no: YHCR1900 Case-6-OW-108603. Question: Power Adapter Specification as Adapter Supplied with Monitor not Working
Customer Issue: Power Adapter Specification as Adapter Supplied with Monitor not Working. Solution: If wants to buy locally. Please check three points AC Power Adapter to DC12V 48W (Min.) DC Plug, see the red mark in the table below for details: ...
Part no.: U4600L1 - Case 6-106719 - Issue: Monitor loses its picture, while still running.
Issue: Monitor loses its picture, while still running. If unscrew the bottom cover, turn the unit off, then turn it on. The screen comes back and then losses it's picture again after a few days. Diagnosis: Due to Temperature controller board. When ...
IR Touch Module Assemble User Manual
1. X axis transmitting tube : 1 PCS 2. Y axis transmitting tube : 1 PCS 3. Y axis receiving tube : 1 PCS 4. X axis receiving tube : 1 PCS 5. Screws (KM2.5 * 4mm) : 14 Pcs (2pcs backup) Step 1: Match the No. on the touch frame (No. A match No. A, No. ...
Part no.: AMil-W1730-D12b-AC - Case 6-120162 - Issue: Display is dark
Customer Issue: I can't get the screen up for adjusting the display either. The display is just dark, like it doesn't have power. Solution: Check if the LVDS Cable is loosen or not plugged in. See below for instruction. How to check panel LVDS Cable ...
Part no.: BCPCW4200HDC2D - Case 6-110876 - Question: When turn on, can't see Hard Drive.
Question: Let me introduce myself I work in Fameccanica and I’m a software coordinator. On one of our machines, we have a problem with your graphic display. When you turn on the system, it seems that it can’t see its hard drive. So, what can we do? ...
Part no: IVP1700Ce-USB - Case 6-110883. Question: Hardware having issues?
Customer Issue: The initial test MKA assets model IVP1700CE-USB (April 2021) works fine with our KVM Vertiv, model SC840. The revised MKA model IVP1700CE-USB(July 2022) is the hardware that is having issues. Listed below are problems we are ...
Part NO.: EOPW1900SW-INT01-ELO - Case 6-110783 - Question: How to calibrate touchscreen?
Question 1: Just need to able to calibrate with 8.0.0 but customer is just using single touch only. Answer: We test it (SAWUSBEL61) can work with 8.0.0 properly. Please also specified the requirement in your further orders for ELO driver, so ...
Part no: AMARW1730 - Question: How to set monitor to 1920x1080 resolution.
Customer Question: When we plug it into a PC windows thinks it is a 1920x1200 monitor (recommended resolution). If we choose 1920x1080 as the resolution the monitor puts black bars at the top and bottom of the screen... if we leave it at 1920x1200 ...
Part No.: SCHW4200HB-SIP-V1 - Case 6-OW-110304a - Display developing condensation inside.
Customer Issue: Have found that one of the four displays that has been installed is developing condensation inside. The Anti-Con supply is found to be healthy, and the Anti-Con switch is in the On position. Could you please look into why this would ...
Part No.: YCH1500HB-TR-DC - Case 6-OW-107338 - Male Connector for DC 9-36V Power Input (Model: DC-ME860-508-02G / DC-MC421-350-02G).
Customer Issue: I have a truck of mine that runs a camera system with LCD display provided by your store. The plug was broken or lost or something, anyway, it's just wires showing. Is there a harness you can direct me to, to replace this? Solution: ...
Comparison Report AMil-1900-D8e-AC and AMil-1900-D12e-AC
LCD: Same LCD, video driving circuitry and backlight the same? Yes Keyboard/Trackball Module: Same item? Yes Control interfaces and displays (buttons, indicators) are the same? Yes Power supply: Same module or design? Different models --- previous ...
Part No.: ASKW2400S - Case 6-110804 - Question: Keyboard not working.
Customer Issue: We tried to disconnect and connect the cable, but keyboard didn’t work. Actually, the cable of keyboard and touchpad is the same. We already tried: -connect and disconnect as questioned; -restart the computer same times; -connect to ...
How to disable Auto Dimming in YOP/YCH/YPM using light sensor.
Question: How to disable Auto Dimming in YOP/YCH/YPM using light sensor. Because once you have Auto Dimming Light sensor come with LCD which you can’t change the brightness manually. Answer: Please see below instruction how to disable YOP/YCH/YPM ...
Next page